1. 산업용 컴퓨터를 켠 후 일반적인 오류는 무엇입니까? 그것을 처리하는 방법?
1. After the industrial computer is turned on, after the BIOS detects the CPU, memory, and keyboard, it prompts "Cmos checksum error-Ddfaults loaded".
Generally, it is because the internal and external card resources of the industrial computer conflict with the BIOS, which causes the BIOS to reset. Please press the "DEL" key to enter the CMOS settings, press the F10 key and type "Y" and press Enter to restart the industrial computer to enter the system normally .
2. After the industrial computer is turned on, it can start normally. After the BIOS detects the CPU and memory, it prompts "Keyboar derror or no keyboard present".
Confirm whether the keyboard lock of the industrial computer is locked; confirm whether the keyboard port of the industrial motherboard is connected to the keyboard correctly and whether the connection is firm.
3. After the industrial computer is turned on, it can start normally. After the BIOS detects the CPU and memory, it prompts "Detecting IDE drives...", and then prompts that no hard disk is found, and the industrial computer cannot enter the operating system.
Confirm whether the hard disk has bad sectors; confirm whether the above failure will occur after the industrial computer replaces a hard disk.
4. After the industrial computer is turned on, there is no response from the work indicator, and the industrial computer is not powered on.
Check whether the power supply of the industrial computer is connected; check whether the connection of the industrial computer switch cable is firmly connected to the industrial motherboard; use a multimeter to check whether the industrial computer switch can be turned on normally; replace the same specification power supply test; if it still cannot be turned on, contact the industrial computer manufacturer.
5. After the industrial computer is powered on, the power supply works normally, but the industrial computer has no response.
Confirm whether the CPU and memory are firmly connected to the industrial motherboard; find the industrial motherboard Clear CMOS jumper and clear the BIOS; replace the industrial motherboard of the same model, and check whether the industrial computer can start; if it still fails, contact the industrial computer manufacturer.
6. The industrial computer does not start after it is turned on, but a long-term continuous alarm sound can be heard.
메모리 바가 산업용 마더보드에 단단히 연결되어 있는지 확인하십시오. 메모리 바의 골드 핑거에 이물질이 있는지 확인하십시오. 지우개로 메모리 막대의 금 손가락을 닦고 테스트하십시오. 테스트를 위해 메모리 막대를 다른 메모리 슬롯으로 교체합니다. 테스트할 동일한 사양의 메모리 바를 교체하십시오.
Note: When replacing the CPU and memory, do not touch the other components of the industrial computer to prevent electrostatic damage.
Second, how to deal with the phenomenon that the industrial computer does not respond when it is turned on?
1. If the indicator light on the chassis panel of the industrial computer does not light up and the fan does not turn on, it means that the industrial computer is not connected to the power supply, and the power supply should be checked.
2. The indicator light on the chassis panel of the industrial computer is on, and the fan rotating sound is also heard. Check whether the power indicator light of the monitor is on.
(1) If the power indicator of the monitor does not light up, check whether the power cord of the monitor is connected, and turn on the power switch of the monitor.
(2) 모니터의 전원 표시등이 켜져 있는데 화면에 텍스트가 표시됩니까? 모니터 화면에 디스플레이가 없으면 먼저 모니터의 신호 라인이 산업용 컴퓨터에 연결되었는지 확인하고 신호 라인이 인터페이스에서 그래픽 카드에 단단히 연결되어 있는지 확인하고 산업용 스피커 컴퓨터 섀시가 들릴 수 있습니다.
If the horn emits "Bee...Bee..." two consecutive beeps are relatively short and repeated alarms. It means that the video card of the industrial computer is not inserted well or the contact is bad. At this time, turn off the power, open the case, reinsert the graphics card, and fix the graphics card. If it still crashes and continues to make the aforementioned sound, there may be a problem with the graphics card. You can get it to another industrial computer for debugging. If it still doesn't work, you need to replace the graphics card. If the speaker emits "...di...di...", the interval between each sound is long, and the sound is repeated, because the industrial computer has not detected the memory stick, re-insert the memory stick, and debug on a different memory slot . If it does not work, replace the memory module.

